Force decay evaluation of latex and non-latex orthodontic intraoral elastics: in vivo study

ABSTRACT Objective: This clinical study was conducted in order to evaluate force decay over time of latex and non-latex orthodontic intraoral elastics. Methods: Patients (n = 15) were evaluated using latex and non-latex elastics in the periods of : 0, 1, 3, 12 and 24 hours. The rubber bands were transferred to the testing machine (EMIC DL-500 MF), and force values were recorded after stretching the elastic to a length of 25mm. Paired t test was applied and analysis of variance (ANOVA) was used to evaluate the variation of force generated. LSD (Fisher's least significant difference) post-hoc test was thus employed. Results: As regards the initial forces (zero time), the values of force for non-latex elastic were slightly higher than for the latex elastic. In the subsequent times, the forces generated by the latex elastic showed higher values. Regarding the material degradation, at the end of 24 hours the highest percentage was observed for non-latex elastic. Conclusions: The latex elastics had a more stable behavior during the studied period, compared with non-latex.

RESUMO Objetivo: o objetivo deste estudo clínico foi avaliar e comparar o comportamento dos elásticos de látex e não látex quanto à perda de força ao longo do tempo. Método: os pacientes (n = 15) foram avaliados usando ambos os tipos de material (látex e não látex) em cada tempo: 0, 1, 3, 12 e 24 horas. Os elásticos foram transferidos para a máquina de ensaios mecânicos (EMIC DL-500 MF) e os valores de força foram registrados após a distensão dos elásticos a uma distância de 25 mm. Foi aplicado o teste t pareado, e a análise de variância (ANOVA) foi realizada para verificar a variação das forças geradas em todos os tempos estudados. Em seguida, o teste post-hoc LSD (Fisher's least significant difference) foi aplicado. Resultados: quanto às forças iniciais (tempo zero), os valores de força dos elásticos não látex foram ligeiramente maiores do que dos elásticos de látex. Nos tempos subsequentes, as forças geradas pelos elásticos de látex apresentaram valores superiores às geradas pelos elásticos não látex. Em relação à degradação do material, ao fim do período de 24 horas, o maior percentual foi observado pelos elásticos não látex. Conclusões: os elásticos de látex apresentaram comportamento mais estável durante o período de estudo, em comparação aos não látex.

Effect of thermal cycling on denture base and autopolymerizing reline resins

Objective This study evaluated the fracture toughness (FT) of denture base and autopolymerizing reline resins, with and without thermocycling (T). Material and Methods Specimens of each material (denture base acrylic resin - Lucitone 550 – L; autopolymerizing reline resins - Ufi Gel Hard–UH, Tokuyama Rebase II-TR, New Truliner–NT and Kooliner-K), were produced, notched and divided into two groups (n=10): CG (control group of autopolymerizing reline resins and L): FT tests were performed after polymerization; TG (thermocycled group): FT tests were performed after T (5°C and 55°C for 5,000 cycles). Results: Results (MPa.m1/2) were analyzed by two-way ANOVA and Tukey's test (p=0.05). L exhibited the highest FT mean values in both groups (CG - 2.33; TG - 2.17). For the CG groups, NT showed the highest FT (1.64) among the autopolymerizing reline resins, and K the lowest (1.04). After T, when the autopolymerizing reline resins were compared, a statistically significant difference in FT was found only between the NT (1.46) and TR (1.00). Conclusions Thermocycling increased the FT of K and did not influence the FT of L, UH, TR and NT. .

Bond strength between acrylic resin and maxillofacial silicone

The development of implant dentistry improved the possibilities of rehabilitation with maxillofacial prosthesis. However, clinically it is difficult to bond the silicone to the attachment system. OBJECTIVES: This study aimed to evaluate the effect of an adhesive system on the bond strength between acrylic resin and facial silicone. MATERIAL AND METHODS: A total of 120 samples were fabricated with auto-polymerized acrylic resin and MDX 4-4210 facial silicone. Both materials were bonded through mechanical retentions and/or application of primers (DC 1205 primer and Sofreliner primer S) and adhesive (Silastic Medical Adhesive Type A) or not (control group). Samples were divided into 12 groups according to the method used to attach the silicone to the acrylic resin. All samples were subjected to a T-peel test in a universal testing machine. Failures were classified as adhesive, cohesive or mixed. The data were evaluated by the analysis of variance (ANOVA) and the Tukey's HSD test (α=.05). RESULTS: The highest bond strength values (5.95 N/mm; 3.07 N/mm; 4.75 N/mm) were recorded for the samples that received a Sofreliner primer application. These values were significantly higher when the samples had no scratches and did not receive the application of Silastic Medical Adhesive Type A. CONCLUSIONS: The most common type of failure was adhesive. The use of Sofreliner primer increased the bond strength between the auto-polymerized acrylic resin and the Silastic MDX 4-4210 facial silicone.

Evaluation of tensile bond strength of heat cure and autopolymerizing silicone-based resilient denture liners before and after thermocycling.

Aim: To assess the effect of simulated mouth conditions reproduced with thermocycling on the tensile bond strength of two silicone based resilient denture liners with acrylic resin bases. Materials and Methods: Two silicone-based soft denture liners (Mollosil - Chairside autopolymerization and Molloplast B - Heat polymerization) were tested. For each liner, 30 specimens with a cross-sectional area of 10 Χ 10 mm and thickness 3 mm were processed between two acrylic blocks (Trevalon). Specimens were divided into a control group that was stored for 24 hours in water at 37°C and a test group that was thermocycled (2500 cycles) between baths of 5° and 55°C. Tensile bond strength (kg/cm 2 ) was determined in a universal testing machine using crosshead speed of 5 mm/min. Statistical Analysis Used: The student t-test was used to determine the significance of the difference in bond strength between the two liners. Results: The mean tensile bond strength for control and thermocycled specimens of the two liners were: Mollosil (6.82 kg/cm 2 and 8.41 kg/cm 2 ) and Molloplast-B (16.30 kg/cm 2 and 13.67 kg/cm 2 ), respectively. Comparison of bond strength of control specimens with thermocycled specimens of the liners indicated a significant difference for both Mollosil (P=0.045) and Molloplast-B (P=0.027). Comparison between control specimens of both liners and thermocycled specimens of both liners indicated a highly significant difference (P<0.001). Conclusions: Heat polymerized resilient denture liner Molloplast-B had higher tensile bond strength than autopolymerizing liner Mollosil regardless of thermocycling. The bond strength of Mollosil increased after thermocycling while that of Molloplast-B decreased after thermocycling. Clinical Implications: Although heat-polymerized denture liners require more processing time than autopolymerizing liners, but they display much better adhesion properties to denture base resin and should thus be preferred when soft liner has to be used for a longer duration of time.

Definitive magnetic nasal prosthesis for partial nasal defect.

Maxillofacial trauma refers to any injury to the face or jaw caused by physical force, trauma, the presence of foreign objects, animal or human bites, and burns. Facial defects can be devastating in their impact on physical structure and function of the affected individual, leading to potential compromises in quality of life. Restoration of facial defects, especially nasal defects, is a difficult challenge for both the surgeon and the prosthodontist. Here is a case report of partial nasal defect caused by trauma, rehabilitated with a magnetic nasal prosthesis made with silicone elastomers using mechanical and anatomical retentive aids.

Diferentes técnicas de impresión del tejido blando en implantes / Different impression techniques for the surrounding soft tissue of the implant

La preparación del perfil de emergencia en las restauraciones protésicas y su impronta en el tejido blando constituyen un paso fundamental para conseguir una adecuada estética gingival en la zona pericoronaria. El tejido gingival que rodea el implante por sus características histológicas, tiende a colapsarse durante la toma de la impresión. Para prevenir este inconveniente existen diferentes técnicas, y las más frecuentes son descriptas en este trabajo.

Linear dimensional changes in plaster die models using different elastomeric materials

Dental impression is an important step in the preparation of prostheses since it provides the reproduction of anatomic and surface details of teeth and adjacent structures. The objective of this study was to evaluate the linear dimensional alterations in gypsum dies obtained with different elastomeric materials, using a resin coping impression technique with individual shells. A master cast made of stainless steel with fixed prosthesis characteristics with two prepared abutment teeth was used to obtain the impressions. References points (A, B, C, D, E and F) were recorded on the occlusal and buccal surfaces of abutments to register the distances. The impressions were obtained using the following materials: polyether, mercaptan-polysulfide, addition silicone, and condensation silicone. The transfer impressions were made with custom trays and an irreversible hydrocolloid material and were poured with type IV gypsum. The distances between identified points in gypsum dies were measured using an optical microscope and the results were statistically analyzed by ANOVA (p < 0.05) and Tukey's test. The mean of the distances were registered as follows: addition silicone (AB = 13.6 µm, CD=15.0 µm, EF = 14.6 µm, GH=15.2 µm), mercaptan-polysulfide (AB = 36.0 µm, CD = 36.0 µm, EF = 39.6 µm, GH = 40.6 µm), polyether (AB = 35.2 µm, CD = 35.6 µm, EF = 39.4 µm, GH = 41.4 µm) and condensation silicone (AB = 69.2 µm, CD = 71.0 µm, EF = 80.6 µm, GH = 81.2 µm). All of the measurements found in gypsum dies were compared to those of a master cast. The results demonstrated that the addition silicone provides the best stability of the compounds tested, followed by polyether, polysulfide and condensation silicone. No statistical differences were obtained between polyether and mercaptan-polysulfide materials.

Effect of ageing and immersion in different beverages on properties of denture lining materials

OBJECTIVES: To evaluate the color stability and hardness of two denture liners obtained by direct and indirect techniques, after thermal cycling and immersion in beverages that can cause staining of teeth. MATERIAL AND METHODS: Seventy disc-shaped specimens (18 x 3 mm) processed by direct (DT) and indirect techniques (IT) were made from Elite soft (n=35) and Kooliner (n=35) denture liners. For each material and technique, 10 specimens were subjected to thermal cycling (3,000 cycles) and 25 specimens were stored in water, coffee, tea, soda and red wine for 36 days. The values of color change, Shore A hardness (Elite soft) and Knoop hardness (Kooliner) were obtained. The data were subjected to ANOVA, Tukey's multiple-comparison test, and Kruskal-Wallis test (P<0.05). RESULTS: The thermal cycling promoted a decrease on hardness of Kooliner regardless of the technique used (Initial: 9.09± 1.61; Thermal cycling: 7.77± 1.47) and promoted an increase in the hardness in the DT for Elite Soft (Initial: 40.63± 1.07; Thermal cycling: 43.53± 1.03); hardness of Kooliner (DT: 8.76± 0.95; IT: 7.70± 1.62) and Elite Soft (DT: 42.75± 1.54; IT=39.30± 2.31) from the DT suffered an increase after the immersion in the beverages. The thermal cycling promoted color change only for Kooliner in the IT. Immersion in the beverages did not promote color change for Elite in both techniques. The control group of the DT of Kooliner showed a significant color change. Wine and coffee produced the greatest color change in the DT only for Elite Soft when compared to the other beverages. CONCLUSION: The three variation factors promoted alteration on hardness and color of the tested denture lining materials.

Visual evaluation of color stability after accelerated aging of pigmented and nonpigmented silicones to be used in facial prostheses.

OBJECTIVES: The objective of this study was to evaluate by a visual method of comparison the color stability of nonpigmented and pigmented facial silicones after accelerated aging. MATERIALS AND METHODS: Two kinds of silicones were used in this study; one specifically formulated for facial prostheses and the other an acetic silicone for industrial use. Twenty-four trial bodies were made for each silicone. These were divided into colorless and intrinsically pigmented groups: ceramic, make-up, and iron oxide. The groups were submitted to accelerated aging for nonmetallic materials. An initial reading and subsequent readings were made at 163, 351, 692, and 1000 hours using a visual method of comparison. The values were annotated in a spreadsheet by two observers, according to scores elaborated for this study. RESULTS: All groups presented color stability in the visual method. According to the results obtained and analyzed in this study, we can conclude that both silicones, Silastic 732 RTV and Silastic MDX 4-4210, behaved similarly, they can therefore be indicated for use in maxillofacial prosthesis. The time factor of aging influenced negatively, independently of the pigmentation, or lack of it, and of silicones and no group had visually noticeable alterations in any of the accelerated aging time, independently of the addition or not of pigments.

Color stability after accelerated aging of two silicones, pigmented or not, for use in facial prostheses

One of the greatest challenges faced by buccomaxillofacial prosthetists is to reproduce the patient's exact skin color and provide adequate esthetics. To reach this objective, professionals must use materials with easy characterization and that maintain color over long periods of time. The objective of this study was, thus, to evaluate the color stability of two types of silicones, Silastic 732 and Silastic MDX4-4210. Twenty-four test specimens were made from each type of silicone and were divided into a colorless group and groups intrinsically pigmented with ceramics, cosmetics or iron oxide. The specimens were submitted to an accelerated system of aging for non-metallic materials. Readings were carried out initially and after periods corresponding to 163, 351, 692 and 1,000 hours of aging, using a reflection spectrophotometer analysis, and color alterations were calculated by the CIE L*a*b* system. The data were submitted to variance analysis and Tukey's test at a 5 percent level of probability. The results demonstrated that, irrespective of the period of time analyzed, all the materials underwent some type of chromatic alteration (ÄE > 0). The test specimens made with Silastic 732 and MDX4-4210, without pigmentation, presented the lowest color alteration values after 1,000 hours of aging. Of the pigments, ceramic presented the lowest color alteration values and cosmetic powder presented the highest values. Thus, it may be concluded that the materials without the incorporation of pigments presented similar color alteration values, and did not differ statistically. The cosmetic powder used in this study was the pigment that most altered the color of the test specimens.

Effect of conventional and experimental gingival retraction solutions on the tensile strength and inhibition of polymerization of four types of impression materials

In the present study, two types of tests (tensile strength test and polymerization inhibition test) were performed to evaluate the physical and chemical properties of four impression materials [a polysulfide (Permlastic), a polyether (Impregum), a condensation silicone (Xantopren) and a polyvinylsiloxane (Aquasil) ,3; when polymerized in contact with of one conventional (Hemostop) and two experimental (Vislin and Afrin) gingival retraction solutions. For the tensile strength test, the impression materials were mixed and packed into a steel plate with perforations that had residues of the gingival retraction solutions. After polymerization, the specimens were tested in tensile strength in a universal testing machine. For the polymerization inhibition test, specimens were obtained after taking impressions from a matrix with perforations that contained 1 drop of the gingival retraction solutions. Two independent examiners decided on whether or not impression material remnants remained unpolymerized, indicating interference of the chemical solutions. Based on the analysis of the results of both tests, the following conclusions were reached: 1. The tensile strength of the polysulfide decreased after contact with Hemostop and Afrin. 2. None of the chemical solutions inhibited the polymerization of the polysulfide; 3. The polyether presented lower tensile strength after polymerization in contact with the three gingival retraction agents; 4. The polyether had its polymerization inhibited only by Hemostop; 5. None of the chemical solutions affected the tensile strength of the condensation silicone; 6. Only Hemostop inhibited the polymerization of the condensation silicone; 7. The polyvinylsiloxane specimens polymerized in contact with Hemostop had significantly lower tensile strength; 8. Neither of the chemical solutions (Afrin and Vislin) affected the tensile strength of the polyvinylsiloxane and the condensation silicone; 9. Results of ...

Evaluation of dimensional change and detail reproduction in silicones for facial prostheses

El objetivo de este estudio fue evaluar la estabilidad dimensional y el mantenimiento de detalles, de dos siliconas para uso en prótesis facial, bajo la influencia de la desinfecciónquímica y del tiempo de almacenamiento. Fueron obtenidos 28probetas, una mitad con silicona Silastic MDX 4-4210 y, la otra, con silicona Silastic 732 RTV. Las probetas fueron divididas en 4 grupos: Silastic 732 RTV y Silastic MDX 4-4210 con desinfección de 3 veces por semana con efferdent y sin desinfección. El análisis de alteración dimensional fue hecho en un microscopio electrónico comparador y el mantenimiento de detalles fue observado en una lupa estereoscópica, inmediatamente y 2 meses después de la confección de los cuerpos deprueba. Después de la obtención de los resultados, fue aplicado análisis de variancia (ANOVA), seguido del Test de Tukey con confiabilidad de 1%. El factor tiempo del almacenaje influencióestadísticamente en la estabilidad dimensional: Silastic MDX 4-4210 presentó una menor contracción que Silastic 732 RTV. La desinfección química no alteró significativamente laestabilidad dimensional en los materiales utilizados. Con respecto al mantenimiento de detalles, no se observó alteración de los valores en ninguno de los materiales analizados independientemente del período de almacenaje o desinfección.

Comparison between textured silicone implants and those bonded with expanded polytetrafluoroethylene in rats

PURPOSE: Comparison of the inflammatory reaction promoted by textured silicone implants and that caused by the implant bonded with e-ptfe. METHODS: One-hundred and fifty rats were divided into three equal groups (control, silicone, and bonded e-ptfe). These groups were subdivided into five groups, according to the second operation, i.e., 7,30,60,90 and 180 days. Histology of the peri-implant tissue was analyzed by morphometry with blood count (neutrophilos, lymphocytes, macrophages, fibroblasts and capillaries). RESULTS: Comparison of subgroups 7,30,60,90, 180 days: - neutrophils: silicone: > in subgroup 7 days; bonded e-ptfe: > in subgroups 7 and 30 days; - lymphocytes: silicone: > in subgroup 7 and 180 days; bonded e-ptfe: > in subgroup 180 days; - macrophages: silicone: > in subgroup 7 and 60 days; bonded e-ptfe: > in subgroup 7,30 and 60 days; - fibroblasts: silicone: > in subgroup 30 and 60 days;- vascular volume: silicone: in subgroup 7, 60 and 90 days; bonded e-ptfe: > in subgroup 7 days. Comparison of groups: neutrophils : 7 days: > in silicone and bonded e-ptfe; 30 days: > in bonded e-ptfe; - lymphocytes: - 7,30,90 and 180 days: in the control; macrophages: - 7,30 and 60 days: > in silicone & bonded e-ptfe; 180 days > in silicone; fibroblasts: - 7,30 and 90 days: > in silicone and bonded e-ptfe; 180 days: > in bonded e-ptfe; vascular volume 7,60,90 and 180 days: > in silicone and bonded e-ptfe; 30 days: > in bonded e-ptfe. CONCLUSIONS: The acute stage of the inflammatory response was more severe and irregular in the silicone implant; both the silicone implant and the silicone bonded with e-ptfe promoted chronic inflammatory reaction and weak foreign body inflammatory response. These reactions were greater in the silicone implant group.

OBJETIVO: Comparar a reação inflamatória provocada pelo implante de silicone texturizado, com aquela causada por este recoberto com PTFE-E. MÉTODOS: Foram utilizadas 150 ratas, divididos em três grupos igruais (controle, silicone e recoberto PTFE-E). Os grupos foram subdivididos em cinco subgrupos, ou seja, 7, 30, 60, 90 e 180 dias, de acordo com a data do segundo ato operatório. O tecido perimplante foi analisado histologicamente, por meio de técnica morfométrica, com contagem de neutrófilos, linfócitos, macrófagos, fibroblastos e capilares. RESULTADOS: Comparação dos subgrupos 7, 30, 60, 90 180 dias: - neutrófilos - silicone: > no subgrupo 7 dias; rec-ptfe: > nos subgrupos 7 e 30 dias; - linfócitos: silicone: > no subgrupo 7 e 180 dias; rec-ptfe: > no subgrupo 180 dias; - macrófagos: silicone: > no subgrupo 7 e 60 dias; rec-ptfe: > no subgrupo 7, 30 e 60 dias; - fibroblastos: silicone: > no subgrupo 30 e 60 dias; - volume vascular: silicone: > no subrupo 7, 60 e 90 dias; rec-ptfe: > no subgrupo 7 dias . Comparação dos gurpos: - neutrófilos - 7 dias: > no silicone e rec-ptfe; 30 dias: > no rec-ptfe; - linfócitos - 7, 30, 90 e 180 dias: > no controle; - macrófagos - 7, 30 e 60 dias: > no silcone e rec-ptfe; 180 dias: > no silicone; - fibroblastos - 7, 30 e 90 dias: > no silicone e rec-ptfe; 180 dias: > no rec-ptfe; - volume vascular - 7, 60, 90 e 180 dias: > no silicone e rec-ptfe; 30 dias: > no rec-ptfe. CONCLUSÕES: A fase aguda da reação inflamatória foi mais intensa e irregular no implante de silicone; tanto o implante de silicone como o de silicone recoberto por ptfe-e induziram a reação inflamatória crônica e a fraca reação inflamatória tipo corpo estranho. Estas forram maiores no implante de silicone.

Análisis de las alteraciones de la posición de los dientes artificiales de prótesis totales maxilares en función del tamaño del arco / Analysis of position alterations in artificial teeth of maxillary complete dentures in function of the arch size

El propósito de este trabajo fue analizar en prótesis totales maxilares la influencia del tamaño de los arcos en el movimiento de dientes artificiales cuando los mismos se someten a las inclusiones con barrera de yeso tipo IV (especial), polimerizado en microondas y medidas gráficamente por computadora. Veinte y una réplicas de prótesis que se habían construido previamente, fueran divididos en tres grupos: grupo 1, constituido de 7 prótesis maxilares del tamaño pequeño; grupo 2, constituido de 7 prótesis de tamaño medio y, grupo 3, de gran tamaño. Las prótesis habían sido medidas en puntos demarcados previamente en los dientes, con un programa de computación gráfica, después del encerado y después de la polimerización y demuflado. La diferencia entre la medida, en las dos etapas, demostró la ocurrencia de pequeñas alteraciones. Fue concluido, del punto de vista estadístico, que no ha tenido diferencias significativas en las alteraciones de la posición de dientes, en los tres tamaños de modelos estudiados.

The purpose of this study was to evaluate the influence of maxillary arch size on the artificial teeth movement in complete dentures. The maxillary dentures were processed with a barrier-type IV gypsum molding technique, and polymerized by microwave energy. Twenty one dentures were fabricated and equally divided into 3 groups, according to maxillary residual ridge size: G1) small; G2) medium and G3) large size. Reference points were made on the incisal edges of the central incisors and the supporting cusps of the premolar and second molar teeth. Linear distances among reference points, in a horizontal plane, were measured with a computer program (Auto cad 2000) before and after processing denture. Although there were differences between measurements, indicating some movement degree among artificial teeth, the results showed no statistical significantly differences among three groups studied. It was concluded that the maxillary arch size has not influence on the artificial teeth position.

Polishing methods of an alumina-reinforced feldspar ceramic

The purpose of this study was to test the hypothesis that mechanical polishing methods of ceramic surfaces allow similar superficial roughness to that of glazed surfaces. Twenty-five Vitadur Alpha ceramic discs (5 mm x 2 mm) were prepared according to the manufacturer's specifications. All specimens were glazed and randomly assigned to 5 groups (n=5), according to finishing and polishing protocols: G1: glazed (control); G2: diamond bur finishing; G3: G2 + silicon rubber tip polishing; G4: G3 + felt disc/diamond polishing paste; G5: G3 + felt disc impregnated with fine-particle diamond paste. Next, surface roughness means (Ra - æm) were calculated. Qualitative analysis was made by scanning electron microscopy. Surface roughness data were submitted to ANOVA and Tukey's test at 5 percent significance level. G1 and G4 were statistically similar (p>0.05). G2 presented the highest roughness means (p<0.05) followed by groups G3, G5, G4 and G1 in a decreasing order. The hypothesis was partially confirmed as only the mechanical polishing (G4) produced similar superficial roughness to that of surface glazing, although finishing and polishing are technically critical procedures.

O objetivo deste estudo foi testar a hipótese de que o acabamento e o polimento da superfície cerâmica produzem rugosidade superficial semelhante à superfície cerâmica vitrificada. Vinte e cinco corpos-de-prova (5 mm x 2 mm) da cerâmica Vitadur Alpha foram obtidos de acordo com as recomendações do fabricante. Todas os corpos-de-prova foram vitrificados e aleatoriamente divididos em 5 grupos (n=5), de acordo com os seguintes protocolos de acabamento e polimento: G1: vitrificação (controle); G2: abrasão com ponta diamantada; G3: G2 + acabamento com borrachas abrasivas; G4: G3 + polimento com pasta diamantada/disco de feltro; G5: G3 + disco de feltro impregnado com pasta diamantada. Após 6 análises individuais foi obtida 1 média por corpo-de-prova da rugosidade (Ra). A análise qualitativa foi realizada por microscopia eletrônica de varredura. Os valores médios de rugosidade foram submetidos à ANOVA e ao teste de Tukey com nível de significância de 5 por cento. G1 e G4 foram estatisticamente semelhantes (p>0.05). O grupo G2 apresentou o maior valor médio de rugosidade (p<0.05) seguido por G3, G5, G4 e G1 em ordem decrescente. A hipótese foi parcialmente confirmada, pois somente o polimento mecânico do grupo G4 produziu rugosidade superficial semelhante à da superfície vitrificada, embora o acabamento e o polimento sejam procedimentos críticos tecnicamente.

Clinical evaluation of interocclusal recording materials in bilateral free end cases

Cinco combinações de materiais comumente utilizados para registros intermaxilares em casos de extremidades livres bilaterais foram avaliados: base de resina acrílica + cera; base de resina acrílica + pasta zincoenólica; base de resina acrílica + cera + resina Duralay; silicona de condensação; e placa de resina acrílica + hidrocolóide irreversível. Foi realizada a medida da distância vertical entre pontos referenciais em 6 regiões nas bases dos modelos articulados. As medidas obtidas com a articulação manual dos modelos foram tomadas como padrão de comparação para as medidas obtidas com os materiais testados. Os resultados foram submetidos à análise estatística por meio de análise de variância e teste de Tukey. Houve diferença estatisticamente significante (p<0.05) entre a silicona de condensação e a combinação da base de resina acrílica + cera, porém entre os demais materiais não houve diferença estatisticamente significante. A silicona de condensação apresentou as maiores diferenças em relação às medidas obtidas pela articulação manual dos modelos e a combinação da base de resina acrílica + cera apresentou as menores diferenças. Com base nos achados deste estudo, a seguinte escala de reprodutibilidade pode ser estabelecida, do melhor para o pior: base de resina acrílica + cera; placa de resina acrílica + hidrocolóide irreversível; base de resina acrílica + cera + pasta zincoenólica; base de resina acrílica + cera + resina Duralay; e silicona de condensação.

Carga inmediata en el preedéntulo y edéntulo total / Immediate load in the pre-edentulous and totally edentulous patient

Se trataron 66 pacientes preedéntulos y edéntulos totales mediante una prótesis híbrida implantada e instalada en el día. El sistema permite seleccionar el caso en cuanto al número y tamaño de los implantes de acuerdo a la cantidad y calidad ósea de los maxilares y a la oclusión. Estos casos comienzan a ser realizados a partir del mes de mayor de 2002. El seguimiento se realiza a través de controles clínicos radiográficos anuales

Estudo da alteraçäo dimensional em silicones para moldagem polimerizados por reaçäo de condensaçäo / Study of dimensional changes in dental impression condensation silicones

Os silicones de polimerizaçäo por reaçäo de condensaçäo, ainda nos dias de hoje, apresentam larga utilizaçäo no mercado. Devido a esta justificativa, objetivou-se estudar a alteraçäo dimensional destes materiais com os moldes armazenados em duas condiçöes: imersos em água e mantidos em meio ambiente. Utilizou-se um modelo padräo com quatro pilares angulados, apresentando um deles um sulco em forma de 'v', em sua regiäo cervical. A técnica de moldagem realizada foi a do material em consistências densa e fluida em dois estágios, sendo utilizados casquetes metálicos para alívio, que originou espessura padronizada de 2,0mm para a moldagem preliminar. Foram obtidos cinco modelos em gesso pedra tipo IV (Vel- Mix- Kerr), para cada condiçäo experimental estudada. Os modelos foram mensurados em um projetor de perfil (Jones & Lansom- USA) e suas medidas comparadas às do modelo padräo, sendo os resultados obtidos, submetidos à ANOVA ao nível de significância de 5 por cento. Concluiu-se que a marca comercial de silicone por condensaçäo e o meio de armazenagem dos moldes originaram diferenças estatisticamente significantes para a altura e largura dos pilares dos modelos; a característica axial com angulaçäo de 60 e sulco em forma de 'v', originou modelos mais largos com diferenças estatisticamente significantes em relaçäo ao pilar cilíndrico; e näo foi encontrada diferença estatisticamente significante, quando se analisaram as medidas entre os pilares dos modelos, para qualquer condiçäo experimental estudada

Cubetas y adhesivos: su influencia en la exactitud de impresiones tomadas con elastómeros (revisión bibliográfica) / Trays and adhesives: their influence on the accuracy of elastomeric impressions (a review of the literature)

La remoción de una impresión tomada con un material viscoelástico genera una serie de tensiones en la masa del elastómero que se adhiere a la cubeta. Si el adhesivo no es capaz de contrarrestar dichas tensiones, se producirá una deformación permanente de la impresión y por consiguiente el modelo resultante no será exacto